Tag Archives: making

Making A Knife Block

Following a few birthdays a Christmases of giving my dad kitchen knives I have now created a demand for a knife block which I can fulfill as another birthday present. I was fortunate to be able to get a rather nice piece of oak from a generous man in the village, which served this project rather nicely.

This project is the first time I have properly used my table saw, so there was a bit of a learning curve to that.

Milling the Wood

The first step was to square up the block. I very quickly discovered two things: 1) oak is very hard (this really shouldn’t have been a surprise) and 2) the blade on my table saw was very blunt. So I ordered a new table saw blade and set about on the block with hand tools as I waited for that to arrive. I spent a long time and burnt quite a few calories with a plane trying to flatten out the sides and with a hand saw cutting the excess length away.

Cutting the Slots

To cut the slots for the knives I first cut along the length of the block with the table saw in the places I wanted the slots to be, splitting it into a number of planks. My table saw blade was not large enough to cut through the whole block so I had to do multiple cuts of increasing depth from both sides. This ended up giving a rather uneven stepped cut, which I then had to clean up by hand.

Once I had my planks I then cut the slots by making many shallow depth cuts with the table saw. The slots then needed some cleaning up with chisels and sandpaper.

Assembly

I then glued all the planks back together into a single block. I also applied glue to the insides of the slots to seal them. However, this meant that some of the slots became too tight for the knives to fit in so I sanded out the slots with some sandpaper attached to a steel rule with double sided tape.

I then cut down the excess on each side and planed and sanded so it was flush.

I then put a chamfer on the four upright edges with a router.

To make the block slightly more stable I added a wedge at the, which I made from the off cut from cutting the angle into the base. When gluing this piece on I had to weigh down the block otherwise the clamping force would drive it out.

Finishing

There were a number of small internal splits in the wood and gaps from the glue up that needed to be filled in. I had been collecting saw dust and shavings from throughout the make which I could use to fill these gaps. You might have also noticed a very large split in one side. I was not going to fill this in and was instead referring to it as “the feature”.

I ground up the saw dust into a good fine powder by rubbing it between two sanding blocks (rather like a flour mill) and then mixed this with wood glue to make a putty to fill the caps.

Branding

I had some iron bar in an appropriate size so decided to try making a branding iron to put a mark on it. I tried a few designs but decided to do a moth to match a set of rubber moth stamps I have made. I cut a length from the stock, marked the design on one end and went at it with files to cut down to that shape.

I had some difficulty actually using the iron. Getting it the the right heat that it would make a mark but not burn so much as to obscure the smaller detail was quite difficult. I think the design wasn’t ideal. It might have been more successful with narrower raised areas rather than the big flat area of the wings.

I’m not sure how well it actually reads as a moth…so far people have guessed ‘money bag’ and ‘dress’ so it seems not very. I think the loss of the tail detail does hurt readability quite a bit

Finally, I sanded over the whole surface and finished it with danish oil.

 

 

Neolithic Inspired Chess Pieces

Seeing some neolithic figurines I thought they would make good chess pieces. So I made them.

While I decided to have the pieces on each side be different shapes as well as colours I aimed to have them both built on the same principles, with influence from standard chess pieces, to try and keep it easy to see which piece was which. I don’t seem to have been successful as most people I showed them to haven’t correctly identified the pieces.

The pawns for each side where intended to be the basic design motif for each side, with the other pieces being variations on that idea. The pawns where also smaller, and simpler than the rest of the pieces. The bishops where then larger and more elaborate versions of the pawns shape and the king and queen going another step up each. The knights where supposed to be identifiable as having more animalistic features, recalling the horse of the standard chess set. Finally the castle was made to be inanimate.

I sculpted the chess pieces with Daz, which is an air drying clay, and painted them with acrylics. I started by painting each peice in multiple coats of very wet paint in their main colour. I then, after letting them dry, went over all the groves with wet paint in the second colour (getting quite a lot of paint outside of the grooves as well. Finally I dry brushed over the surface in the main colour, which covered up the paint that had escaped the grooves.

The White Pieces

Pawns

« of 5 »
By Juergen E. Walkowitz – Own work / Photo importée du Wiki allemand, Public Domain, https://commons.wikimedia.org/
w/index.php?curid=647183

The white pawns were based on the standing stones (menhirs) with faces at Filitosa, dating to 1500 BC. The shape of these pieces has earned the white side the name of stone men or, less generously, potato men.

Castles

« of 3 »

The white castles where based on stones with cup and ring marks, which are common across prehistoric Europe.

Knights

« of 5 »

The white knights are based on neolithic ram figurines. I added a mouth and eyes, which end up giving them a rather wonderful Muppet like expression.

Bishops

« of 4 »

The bishops are simply a larger version of the pawns with more details. For some reason people often interpret them as knights, thinking they look like an actual human knight.

King and Queen

« of 4 »
« of 4 »

The king and queen take some inspiration from a set of bronze age figurines with wide dress like bases. The differences between the king and queen are quite minimal, with the king being slightly larger and having a bigger head with markings indicating a crown. However, despite this, people have had no difficulty distinguishing them.

The Red Pieces

From this view one of the problems with the red set is quite obvious – they look quite similar from head on, which makes them a bit harder to play against.

Pawns

« of 4 »

The red pawns are based on a set of figurines from the Vinča culture, which provided the initial inspiration for this project. Their hunched animalistic shape has earned them the nickname of mole men among my family.

Castles

« of 3 »

The red castles have no direct inspiration from any artifact. They are just my idea of an inanimate form that fits within the red pieces general aesthetic.

I am well aware that they look like traffic cones.

Knights

« of 5 »

The problem I encountered with the red knights was that all the red pieces already looked rather like chess knights.I tried to give them a sleeker shape and a large mane to evoke the horse idea but this seemingly did not work as people on first inspection generally think the bishops are the knights.

The ‘mane’ has also been misinterpreted leading them to be called the hedgehogs.

Bishops

« of 3 »

The red bishops are simply enlarged versions of the pawns with more decorations. I gave them a crest with a cut into the front to mirror the slit in the head of the bishop in the standard chess set.

King and Queen

« of 3 »
« of 3 »

One again the king and queen are larger versions of the same form as the pawns,with the king being distinguished by a large transverse crest like crown.


Conclusion

I really like how these turned out. My favourite pieces are probably the red king and the white castles and knights. The unfortunate thing is that I neither like nor am good at chess.

Knitting a pointy hat

This project probably reveals the fact that I have a mild obsession with pointy hats. I just think they’re neat. Unfortunately at the height of the some of the warmest weather we have had I  have picked the worst time to make this…

This is my first knitting project with a pattern I designed, although ‘designed’ is putting it rather strongly as it is essentially a cone. It is primarily moss stitch, which takes a bit of thinking about to work out how to correctly reduce (but luckily for you I have already done this) with some ribbing and is made in two halves, which are then stitched together. If you have larger needles and a smaller head than I do or round knitting needles you may be able to make the hat all in one piece. 

For this project I used size 8 needles and hayfeild bonus aran tweed yarn 

To start I knitted a test square to find out how many stitches per length I was working at and measured around my head to work out how many stitches I would need to cast on to start with. This came to 64 stitches for each half. 

So,  the pattern for each half is as follows:

Cast on 64 (I used Tillybuddy’s very stretchy cast on) leaving a reasonable tail.

15 lines of K2P2.

16 lines of moss stitch, which goes like  (repeat this sequence 4 times): 

  • 2 lines K1P1.
  • 2 lines P1K1.

120 lines of reducing moss, which goes like (repeat this sequence 15 times):

  • P2tog, K1P1 until last two sts, K2tog.
  • P1K1.
  • K1P1.
  • K1P1.
  • K2tog, P1K1 until last two sts, P2tog.
  • K1P1.
  • P1K1.
  • P1K1.

P2tog, K2tog.

Cast off  leaving a tail long enough to sew most of one edge  (you should only be casting off two stitches).

Repeat this pattern twice and then lay one half on top of the other and sew along the seams with the tails, on each half the tail from the base and the point should meet some way in the middle and be tied together. Now turn the hat inside out and it should be complete! 

 

Knitting Finger-less Gloves

This is my first knitting project so I was obviously following a tutorial so I will once again just redirect to that and give any alterations I made. 

http://www.instructables.com/id/How-to-knit-close-fitting-fingerless-gloves/

My gloves did not end up looking a great deal like the ones in the tutorial, a lot of this is due to having to change the pattern to fit my hands. I started by casting on 46 stitches which is a fair few more than in the tutorial. I also put in a few extra rows for the thumbs to fit my (so I have been told) wide thumbs but this still ended up being a little tight. I cut down the length of ribbing over the fingers a fair bit partly because I thought that would look better and partly because I was concerned I would run out of wool (I ran out of wool anyway so so much for that). The final change is the switch in the stockinette around the wrist from knit on the outside to purl on the outside, this was entirely a mistake but I ended up liking it.

What I actually ended up having most trouble with was the stitching, which ended up a bit of a hodgepodged mess that I’m sure will fall apart eventually.

   One point of interest is that none of the pictures are of me wearing both the gloves owing to the difficulty of taking a picture of both of your own hands.

Renovating An Old Rebec (Part 1)

 

This instrument caught my eye in my granny’s house where the carved head was poking out from on top of a cupboard so I got it down and found something desperately in need of some attention. After consulting with her it was identified as a rebec, which is an old relative of a violin, with only 3 strings and half round body somewhat resembling that of a lute. This particular rebec had clearly taken a bit of a beating over the years and a number of parts where either missing or broken, so I thought I would take it upon myself to try and repair it and get it back to a playable state.

The keen eyed among you will have noticed that this is listed as part 1 and that is because at the time of writing I have only got so far with this project and will not be able to work any further on it for a while what with university and not having access to my woodworking tools. Therefore, this article will include a rundown of the state of the rebec and what things I need to do and how I am thinking I will do them and then also a more usual description of how I did what I have done so far.

  

 The state of things

The first part that is broken is the soundboard, which is heavily cracked to the point of probably not being sturdy enough to support the bridge anymore. This is the part that I have already made a replacement for so more details on that will follow later in the article.

There is currently only one of the three tuning pegs remaining, but the one that if left is in good condition. These are going to be one of the trickier things to make as they really have to be turned and as I continue to not have a lathe that is rather difficult. What you can use to make the tapered section of the pegs, which is the only part where the shape is actually important (for the rest it is purely aesthetic), is something that is essentially an oversized pencil sharpener. So, an option would be to get one of them to form the tapered part and then to try and hand carve the heads on the pegs but that seems like it will be unlikely that I will be able to make them much of a match to the original one. A last resort would be to just try and either buy two that match the original or a completely new set of three but that seems to go rather against the spirit of the thing.

Another part that is missing is a peg that goes into the end of the body onto which the tail piece attaches, which is the part the strings are attached to. This is another part that would be quite a small and easy part to make on a lathe but trying to make it without is much more challenging.

The last part that is entirely missing is the bridge. I think this should be relatively easy to make and I should be able to follow a fairly similar process to what I used to make the body and I am also hoping that I should be able to use the same piece of wood.  

 

The rebec came with a bow that is currently missing its hair but is otherwise in good condition. I can’t quite tell how the hair was originally attached and it may end up being rather tricky to replace so I will probably just use a regular violin bow on it initially.

 

Making the sound board

For the sound board I bought a set of sheets intended for the soundboard of a small guitar, with one of the sheets being large enough for the rebec. I traced the shape of the original soundboard on to a piece of paper and then stuck this to the wood. I cut roughly around the outside with a small hacksaw, taking care to stay on the outside of the line and then sanded to the final shape.

The next step was the trickiest, which was cutting the holes in the sound board. These being the two large ‘F’ holes (which aren’t actually f shaped in this case) and the four smaller holes that make up the decorative design towards the top. To cut these holes I first drilled a hole inside the space to be cut out to insert a coping saw blade through. I then cut the rough shape using the coping saw, in the process of which I snapped a lot of blades, which I think is partly due to the blades I had to hand being slightly to thin. Once I had cut one of the F’s I then took a trace of its inside shape to make sure the second once matched, which was necessary as that feature did not show up well on the original tracing due to the sound board being cracked and giving way under the pressure of the pencil. I then refined the shape of all of the holes using needle files, which was slow work as the files are meant for metal and are not very efficient at cutting wood but they were the only thing I had that would fit in the small space.

I then used a plane and chisels to put a slight dome on the soundboard, with it being thickest at the bridge. I then carved the design around the four small holes using chisels and a craft knife. My carving ended up looking a fair bit chunkier and clumsier than the original but was ok considering I don’t really have any tools for that sort of work. Finally, I sanded over the whole surface to smooth it up and remove any marks left from the plane or chisels.

All that remains is to remove the original soundboard and glue this one in its place.

 

….and then do all the other things I talked about earlier, which will come in part two, eventually.

EDIT: part 2 is here!

Making A Leather Belt Bag

This is the first project I undertook after having the idea to make this website so it will also be the first one that can form a full tutorial with process pictures throughout. 

The Tools I used 

  1. Leather punch. Used for punching holes of various sizes.
  2. Diamond stitching punches. Used to create the holes for stitching with even spacing. Diamond refers to the shape of the cutting point and not the material.
  3. Leather rivets. 
  4. Rubber mallet. Used for cutting with the stitching punches and for the rivets.
  5. Sturdy rounded needles.  
  6. Stitching groover. Used to mark a line a consistent distance from the edge for where the stitching will go 
  7. Edge kote. Used to finish the exposed edges. Other processes can be used depending on your leather but I found this leather was too thin to burnish.
  8. Chalk. For marking up the leather. 
  9. Spatula. For spreading the edge kote.
  10. Pliers. Useful for pulling the needles through the leather and saving your hands.
  11. Glue.  For holing pieces together while putting in stitching or rivet holes. The type isn’t hugely important so long as it says its suitable for leather.
  12. Waxed linen thread.

How I Made It

I began by sketching some ideas of what I wanted the bag to look like, finding various references on the internet  and picking out ideas and shapes that I liked. Then I drew up the pattern based off of these sketches (its at this point in writing the article that I realize I have no pictures of my pattern so have already failed in what I claimed I would have not one paragraph in). To make the pattern first I drew out the shape I wanted the front of the bag to have (at this point you should check to see that things like your phone or camera that you might want to carry fit into this shape with space to spare). Then  I copied out this shape again for the lower half of the back. Here I needed to decide how much depth I wanted the bag to have (again basing this off of the size of things that need to fit in the bag).  I took this value and added around 1.5-2cm on to this and then drew two parallel lines up from the top corners of the pattern for the back piece, this will be the bit that goes over the top of the opening to the bag. Then I turned the original shape for the front upside down and, starting from the end of the parallel lines, I traced about half way up it and then drew a straight line across. This part is the bit that folds over the front. 

Then I measured the distance around the edge of the front shape, excluding the top edge and drew  out a rectangle of this length (I would recommend adding a bit to this length ans it was quite a bit of work to make this piece fit and it would have been easier if it had been oversize and I just cut off the excess) and with a width the same as the ‘bag depth plus 1.5-2cm’ distance I used before. This is the piece which joins the front and back parts of the bag. Finally I made pattern for the buckle fixings, which are very dependent on the buckle you will be using.   

    

The main dimensions that are important for the part that will hold the buckle are shown in the diagram. The width of the part, a, must be slightly narrower then the inside width of the buckle. There needs to be a  hole of width b that is slightly wider than the width of the prong of the buckle and of length d that is sufficient for the prong to rotate through a large enough angle to function. Finally it need to be long enough in c to loop round the buckle and have enough spare to be stitched and riveted to the front part. For the part that goes through the buckle it simply has to be of width a and also be of sufficient length. The shape for the ends of these parts is mostly an aesthetic choice. I chose to have them both be the same at the ends but they could be different.

Finally I drew up two small rectangles to go on the back which the belt will go through. These just need to be long enough to fit the width of a belt plus have room on either side to be attached by. 

When I had drawn and cut out all the patterns on card I then arranged them on my sheets of leather trying to make the most efficient use of the material. I then used chalk to trace around the patterns and mark onto the leather. Then I cut out the pieces using a pair of textile scissors. This is probably are not the most ideal way to cut leather but it seemed to work well enough.

Now seems an appropriate time for a short side note about the leather I am using. As I did not buy the leather myself and It came as a collection of cut offs I am not entirely sure as to exactly what kind of leather it is. The important thing about it for this project is that it is fairly thin and flexible. Trying to make the bag with stiffer leather would be quite tricky.


I started by attaching the buckle to its piece of leather. I slotted the prong through the hole then wrapped the piece around the buckle. I then punched a hole through both layers and attached them together with a rivet. The rivets come in two parts one with a smooth face and the other a hole in its surface and a rod that fits into the first part. To fit them together place the first part in the hole then put the other part in from the other side. Then hit it with the mallet from the backside to fix the rivet in place. 

I then use a stitching punch to put a line of holes just beneath the buckle and stitched along this line. Leather stitching is done with two needles at other end of the thread in a way called ‘saddle stitch’. The first thing do do is thread the needles, which includes an extra step to secure the tread as otherwise it has a tendency to get pulled out as you pass it through a hole. First pass the thread through the eye of the needle then twist part way along the thread that has come through the eye to open up a hole through which you put the end of the needle. Then pull it tight. Ideally you would leave more tread than I did in the pictures as this was just an example I didn’t use too much thread for it.   

Once the needles are threaded start by putting one needle through the first hole and drawing it through until there is half the thread on each side of the hole. Then pass one of the needles through the next hole from one side and then the other needle through the same hole from the other side. The diagram shows what the stitching should be like. Repeat this along  the whole length and, when you reach the end go back a few stitches and then take one thread one stitch further and tie them off. It isn’t strictly necessary to tie off but I like to be doubly safe. 

I then ran around the edge where I wanted yo put the stitching with the stitching groover. It was easier to do this before attaching it to the other piece even through there were a few more steps before I came to the stitching. I also painted the exposed edge with a few layers of edge kote as it would be imposible to do this once it was attached without also getting it on the front piece. To apply the edge kote I used a metal spatula though I would guess that a paint brush would actually be more effective. I applied a layer and then let it dry before sanding it flat and applying another layer. I repeated this until A layer looked good enough left shiny.

I then glued the buckle piece into place on the front part of the bag and punched two holes and riveted through them. Punching these holes is a bit tricky as it is necessary to bunch up some of the leather to get it far enough into the jaws of the punch.  I then punched the stitching holes and stitched it.

 I then repeated pretty much the same process to attach the other part of the the buckle arrangement to the back piece (I can not seem to find what the part that goes through the buckle is called) and then again with the two belt loops. 

I then began stitching the side piece on to the front piece. I couldn’t get it all lined up in one go so I lined up one part and then punched the holes and stitched them before moving on to punch the holes for the next section. I had to go very slow around the bends using the 2 pronged punch and only going a few stitches at a time. When I got to the end I found I really had to stretch the leather to make it reach all the way round but hopefully anyone following along will not have this trouble as they should have added on some extra length. I then repeated this process to attach the back.

I then applied edge kote around the remaining edges and finished it off by punching the holes for the buckle prong to go through. To work out the position for this I just did a test fit and marked where the prong wanted to go though and then punched a hole there. 


 

If you have followed this you ought to now have yourself a nice leather belt bag. My intention when making it was for the too loops on the back to go on either side of a belt loop on your trousers so as too hold it in place. Alternatively to save having to undo your trouser belt whenever you want to put it on or off you could make or buy a dedicated belt to put it on. If anyone our there does make one I would love to see a picture of your results (though I am not expecting anything any time soon the amount of traffic I have at the moment). 

Making A Bamboo Notched Flute

This style of flute is among the oldest and most straightforward to make instruments. Flutes of this style are quite widespread with examples being the Quena from the Andes and the shakuhachi from Japan. While it is fairly easy to make I found it rather difficult to play even compared to regular flutes which are already fairly tricky. The flute works by sealing the hole with the area bellow your bottom lip and then blowing down over the notch to create the vibrations in the instrument. Covering the finger holes  then changes the note as with an ordinary flute or a recorder.

How I Made It 

To start the project I selected an appropriate length of bamboo. Bamboo is ideal for this sort of instrument as it is already hollow most of the way down, with solid parts only at the divisions between the sections, called nodes. Luckily we have some fairly large bamboo in our garden, which made sourcing a piece very straight forward. Although this bamboo has somewhat thinker walls than would be ideal. When I found a part with fairly large diameter and two sections spanning roughly 30cm I sawed through it just inside of each of the nodes leaving a tube that was open at each end and had a solid node in the middle. The next stage was to open up the node in the middle, which proved to be a reasonable amount of work. The only thing I has that was both thin and long enough was a length of threaded rod, which I used to ram down the bamboo it try and knock out the middle of the node. Once a hole had opened up I used double sided tape to attach sandpaper to the rod and used that to widen the hole and clean up the inside.

The next stage is working out where to place place the finger holes, to do this I used the flutomat calculator. I entered dimensions and then tried different scales until I had a set of holes that would fit nicely on the flute. Where the calculator says embouchure it is referring to the hole that you would blow across on an ordinary flute, for this design this is effectively the end of the flute. Now the flute needs to be cut down so that its overall length is the length given for the embouchure.

I then drilled the holes. Bamboo has a sort of groove running down each segment, with each one being on the opposite side to on adjacent segments, when drilling the holes I oriented the bamboo such that the two grooves were on the right and left sides rather than top and bottom. It is important to realize that the holes do not need to be all in a straight line down the middle of the flute. Moving them slightly over to either side will make it much more natural to hold so, once you have marked up where each hole needs to be try holding the flute and see where your fingers naturally want to go  (obviously only moving them side to side and not further up or down the flute). This is where you should place the holes. I first ran over where I was going to place each hole with a half round file so as to give a better surface to drill into. I then drilled a small pilot hole before expanding it to the full width. I then files over it again to give a slight dip around the hole for your fingers to fit in.

Then comes making the mouth piece. I shaped this using a round file. It needs to have a ‘U’ shape with a sharp edge at the bottom. There is quite a lot of variation of the exact shape with some being much shallower and others being deeper like the one I made. I would recommend searching about for different pictures and also experimenting a bit with how it sounds with different shapes. Although you will not be able to add material back once you have taken it off so if you have a shape that sounds good probably don’t take it any further.  

After this all that remains is to give it a nice surface finish, which I did by going over it with sandpaper, working up the grits until it has a shiny surface, which is relatively easy to achieve with bamboo. If you wan’t to go on to paint it you will probably have some difficulty as bamboo does not seem to take well to any paints that I tried, the surface being much too shiny and not absorbent at all. 

Now that you have your flute all that follows is trying to learn to play it, which may prove to be a bit of a struggle. 

Making An Instrument From A Cow Horn

Ok, instrument is a bit of a stretch, I mean like a hunting horn or a war horn sort of thing. You would be hard pressed to get any music out of it. To be honest you are pretty hard pressed to get a single good note out of it. That is because the mouthpiece I made is not particularly good, which is ok because the point of this horn was experimentation. I got myself 3 horns: one really big one and two smaller ones, one that looked really nice and the other that had some defects and a rather rough surface. I started working on this one first to try and work out a good way to make them and if it didn’t work it wasn’t a huge loss as I still has the two nicer ones. 

How I Made It 

The horns I bought were pre-cleaned out, if they weren’t there would be a lot of preamble cleaning out the stuff that is on the inside of the horn. this is rather outside the scope of the article as I have no experience with this, if your horns are like this do a bit of searching and you will quite easily find instructions on how to do this. 

There is really very little that has to be done to a cow horn to make it into an instrument, most of it is already pretty much in the required shape. All that needs to be done is to put a hole through the pointy end and make that into a mouthpiece. Horns use a mouthpiece like that of a brass instrument, which are much simpler than what you find on other instruments such as woodwind. You can actually just make do with a plain old pipe with no embellishment at all (this is actually a training exercise sometimes used for people learning brass instruments) but this is a lot harder to play and doesn’t sound so good. The basic shape of a brass mouthpiece is a narrow tube that widens into a bowl like shape, which is where the lips are placed. 

My first method of making a mouthpiece was to cheat and not make one at all and just steal one from a brass instrument and stick it in the horn. To do this I cut a small piece of the point off the end to give a flat face and then drilled a hole through the solid end of the horn into the hollow bit. Then I put the mouthpiece into the hole and it worked pretty well. 

That isn’t really in the spirit of things though (and it didn’t really look that good) so I set about thinking about how I could best make something myself. All the most proper ways to do it such as casting something and turning it on a lathe or turning it from wood were not really options for me. I attempted raising something from sheet metal but that quickly turned out to not be feasible. My next idea was to try to carve the bowl of the mouthpiece into the horn itself. To do this I had to make another cut further up the horn so as to get the larger diameter necessary. The trouble turned out to be that the horn did not take kindly to being carved and it proved impossible to bit a curve into it and I just ended up with a flat edge. This hadn’t really worked but the main trouble was that I had painted myself in to a bit of a corner as the end was now really wide and had a large hole in it, which rather limited my options for new ideas. 

The next plan was to make a piece out of wood that would sit in the gap the last failure had left and then to a carve the bowl of the mouthpiece into that. This also did not really work. Partly because of the wood that I had at the time, which did not take to carving very well, and also because of my tools forming the bowl proved to be rather tricky. Had I had a lathe I think this would have probably worked (though I am still not sure how good a wooden mouthpiece will ever sound) but working with a fairly large set of chisels in poor quality wood it wasn’t really going to work.

 

 

This then leads to my last attempt, which was easy enough to execute but doesn’t work very well. I cut out a ring of wood and curved one side to give it a better surface to blow on and then glued this to the end of the horn. It doesn’t look particularly good and could have been made to look a bit prettier but once I had seen that it wasn’t going to work I didn’t think it was worth it.

Finally I polished up the horn, which was just done by working through steadily finer grades of sandpaper. Because the surface was fairly rough and had some cracks in it it wouldn’t be possible to get it to a really high quality finish. For this stage its important to wear a dust mask as, with any process that produces a lot of dust, it really isn’t something you want to be getting in your lungs.


I was going to record a clip of me playing the horn to demonstrate the sound it makes but I forgot to do it before I left and as I am the only one of my family that plays a brass instrument (and this one is a notably difficult one to play) I can’t ask and of them to record it for me. If I remember to do it when I return home that may be added to this article at some point.


 

During the course of writing this article I came up with an idea for how I might be able to make a mouthpiece. That is to buy a metal tube and then hammer that into to shape. This would probably be quite a complex thing to do but I think would be much more achievable than working from flat sheet. Unfortunately this horn is a bit too far gone for this to work so it will have to be saved to try out on the next one, whenever I end up having the time to make that.